Case for Raspberry Pi 4 b / 4 Model B /4b (Pi 4 Board Not Included) RoHS Compliant

I've been using my Pi 4 without a case since I bought it when it was released, though admittedly it's seen little use. Decided I wanted to try out some software on the Pi and bought the cheapest prime eligible case on amazon, not expecting much but thinking that the Pi would at least be protected. I'm pleasantly surprised. The case is a simple two-part plastic construction with internal clips to hold the Pi board in place. The top then clips on, leaving access to all external and internal ports through perfectly positioned cutouts. There are vents on the underside and even wall mounts. Rubber feet would have made it truly perfect and perhaps an optimal cover over the GPIO pins if you're not using them. But overall it's a cracking case for a bargain price and does exactly what it says on the tin.

Great for the price. Obviously not completely sealed as give access to gpio headers but it's great. Easy to install. Plastic quality is good. Not being used for any heavy lifting, so temperature should be fine.

Great value for money when compared to the official pi case. Really pleased with this purchase. Well finished product, snaps together crisply and everything lines up. There's venting underneath the board and gaps to access the camea / gpio pins. After leaving a pi 4 running for 24 hours, the case isn't too warm - certainly cooler than say a TV set top box would be.

I needed a nice, cheap case for my new Raspberry Pi 4. This was very cheap and is perfect for those who just need a simple case. This case comes in two pieces and snaps together perfectly. The case feels strong, the clear plastic looks great and I can see this lasting me until the death of the Pi itself. I haven't attached any fans but the fixtures present for them look like they will do just fine if I do decide to add one at a later date.

In general, all fits fine. No problems with closing, or anything. Sockets fit great in adequate holes. Only problem is - when installing active cooling, after closing it - top lid is blocking the fan from spinning. It simply pushes the fan down, so it cannot spin - it should be about 1mm higher and it would make it a perfect tiny case. I'm cutting only 1 star down, as they doesn't say anything about being OK for heatsinks with fans in the description.

Fits Pi well but the memory card slot is tight and can use loss of data on the card. well it did for me.

great little case, gives me peace of mind when i accidentally hit or knock my Rpi4, probably not the sturdiest of cases but for the ridiculously low price what else could you expect.

perfect box for the Pi, access to the pins, made of good plastic, can't go wrong

Buono per chiudere il pi4, e non toccarlo piu. Plastica molto fragile, se aperto e chiuso spesso è facile che si rompa

Perfect fit. Reasonable price. Enough ventilation.

This is a well made case, very simple, in clear transparent plastic. The plastic feels solid and not flimsy. It was easy to assemble -- no instructions provided and none needed, as it was trivial to install. There are little tabs to hold the RPi PCB in place, and all the IO openings fitted very well and snugly. Note that this is fanless case. If you need a fan, they have a different product. The current price makes this a great value.

The product is very faithful to description. Besides a few (barely visible) scratches from, I'm assuming, the production process, it is a nice clear case. I rated it lower on durability because after taking it out and mounting it back together again, I noticed a small break (not sure if it was while unmounting or already there). It is very easy to install, basically just two shells that easily snap on together, encasing the raspi perfectly. The ports are all very accessible and the material in excess around them is minimal (as opposite to other cases that may stop certain cable shapes to connect properly through the case). It has cute port names engraved on the case as well, little dents for possible wall mount, the case is very "handeable" if you want to tinker with your raspi as well as leaves the GPIO, display and camera areas of the raspi very accessible to handling without having to fidle with the case. Overall, super cheap and a good begginer protective case if you are more into easy DIY projects and not thinking of getting your raspi too hot! :)

Has nothing to offer other than a shell for the pi.