Bench Grinder Replacement Sharpening Tool Rest Jig For 15cm And 20cm Grinders And

The aluminum is well finished with all edges ground very flat, square, and uniform. The finish is uniform and well anodized. My unit suffered a little in shipping but just cosmetic surface dings.The locking mechanism worked well for me and the handles can be rotated easily for clearance. The unit is very adjustable and able to be positioned in a wide range of positions. If needed the unit can be mounted on a wood block, and you can easily reach any desired height.This represents a great value compared to other similar jigs, such as the Veritas brand jig.

Sturdy rest is versatile, dependable and sturdy. Absolutely, provides the support you need to make perfect grinds on edged tools/blades. I should note there are no instructions included with this rest. However, the installation and set up is very intuitive so the lack of instructions is no big deal. Taylor tools is a fantastic company to deal with as well.

I really like the design. It's simple but flexible for various sharpening jobs. The construction is plenty sturdy for small shops and for chisels or planer blades. It is easily adjustable, but it may take some time to get it right because there are so many areas to deal with.... horizontal, vertical, table tilt, how far the tool protrudes from the clamp. With practice it gets easier. I would like an angle gauge to indicate table tilt, and I found that I had to very forcefully tighten the locking levers to hold my settings during use. That said, I find this tool to be a very good value for the money. Competing systems can cost 3-4 X what this one cost. Even with the fine 120 grit wheel, I do my final honing on a diamond coated bar to get a smooth, sharp cutting edge.

The slot in the platform is too small for a CBN wheel. To mount this on my portable grinding station set up for the Wolverine system would take more work than it's worth. The lockdown handles are too low and hit the bottom before tightening. I would have make it higher to work. Not for me. well made though.

I am terrible at sharpening chisels. To the point where once my chisels get really beat up I will often give up and buy new ones because I messed them up fairly badly. I thought buying a grinder would improve things but I often mangled them because the tool rest was garbage. I bought this and it all came together. I was able to take a really beat up chisel and get it to have a mirror's edge. I took photos of the process as well as a video showing how I used the tool rest. Now I am slightly less terrible, but have working chisels again!I added a ton of photos of the process but you can't add captions so this is the gist of it:Video: Showing how you use the jig. I grind it, cool the blade with water which is just off camera, repeat. I check progress as I go because this chisel was really beat up and was initially ground crooked.Photo 1: The beat up chisel I am fixing. It's in rough shape and even has some adhesive stuck to the blade.Photo 2: Squaring up the chisel in the holder using a speed squarePhoto 3: The grinder with the tool rest installed. I put a 3/4" thick board between the grinder and the tablePhoto 4: You can see you you can change the blade angle and distance to accommodate a wide variety of chisels. I eyeballed the angle as it's a little tricky to figure out since you can move the tool in so many directions and distances from the wheel.Photo 5: This board is a bit short. I'll reseat it later and extend it a few inches. It still works just fine so I am not in a rush.Photo 6: End result. Not perfect, but good enough!Photo 7: You can see the hollow grind here.Photo 8: Finding the angle to see how I did. I was off and it's 20 degrees instead of 25. Good enough for my needs and if I have issues I can fix it later.Photo 9: Honing time! I use DMT 8-Inch Dia-Sharp Continuous diamond stones in an extra course to set the bevel, then move onto fine and extra extra fine. My extra course stone is fairly worn so its closer to a course now. Above I have various sheets of sandpaper glued to a 12x12 granite tile with spray adhesive. The tile itself is glued to an old piece of plywood with a couple of shims on the side to help keep it in place. Lubricant is water with a drop of dish soap in a spray bottle.Photo 10: Setting the angle for the sharpening jig.Photo 11-12: I am terrible at freehand and this jig cost $16. Its not as nice as the fancy expensive ones but its better than freehand and does the job https://www.amazon.com/WoodRiver-Honing-Guide/dp/B0035Y439CPhoto 13-14: The initial bevel off of the coarse diamond stone. You can see the wire at the top and it's wavy because the grind is uneven. That is on the operator. I was going for close enough and hopefully I will improve with practice.Photo 15: This is after the fine diamond stonePhoto 16: This is after the extra extra fine diamond stone. It's already very sharp.Photo 17-19: Going through finer and finer grits of sandpaper. I started at 1200 grit and ended at 7000 grit polishing paper. I don't think I got it on Amazon as its not in my order history, but Amazon ultrafine polishing paper.Photo 20: Finished! It is ultra sharp and down to a mirrors edge. Literally! Check out the reflection of the pencil in the bevel.I hope this was helpful, I wanted to show you how this jig fit into the sharpening process because for me it really was the missing piece to being able to effective sharpen my chisels and hand planes.